Innopak CXL is a cross-linked, water- resistant, high-energy emulsion.
Innopak CXL AL is a cross-linked, aluminized, high-energy emulsion.
Innopak CXL MS is a cross-linked, water- resistant, high-energy, aluminized emulsion and consists of solid sensitizer for an increased level of resistance to excessive shock from adjacent blast holes.
Innopak is available in a wide range of lengths and diameters.
Product density is ideal for sinking in wet holes.
Nominal density: 1.20 g/cm³
Velocity of Detonation (VOD): 3500 m/s to 6200 m/s (11,500 ft/s to 20,340 ft/s) dependent on application, diameter, confinement and density.
RWS and RBS calculated with ANFO density 0.80 g/cc and effective energy 2.260 kJ/kg.
Innopak CXL is booster sensitive. Minimum primer is a 227 g (1/2 lb) cast booster initiated by a high strength detonator (No. 8 strength or greater base charge).
Innopak CXL cannot be directly initiated with detonating cord or detonators.
Always allow Innopak CXL ample time to warm to borehole temperature.
Consult with a BME Technical Representative for additional priming and initiation guidance.
Minimum priming requirement of a 227 g (1/2 lb) cast booster.
Maximum hole depth depends on product selection, hole diameter, product densities, and the presence of water.
Please contact a BME Technical Representative for additional guidance.
This product may be used in ground temperatures from to a maximum of 65°C (150°F) . If the application requires use outside this temperature range please contact a BME Technical Representative for additional guidance.
This product is not formulated for use in reactive ground. Reactive ground is typically characterised by the presence of sulphide mineralization.
If the application requires use in known reactive ground, or in untested sulphide bearing ground, please contact a BME Technical Representative for additional guidance.
All explosives must be stored in accordance with local, state and federal regulations.
Allow Innopak to warm to borehole temperature when used in cold weather.
Product Risk Profile
All explosives are classified as dangerous goods and may cause damage to property, personal harm, or death, if not used correctly.
Risk of explosion by shock, friction, fire, or other ignition sources. Classified as hazardous substance, dangerous goods with mass-explosion hazard.
Stable under normal storage conditions.
Temperatures above 65°C (150°F) can be hazardous.
Never load a borehole containing hot or burning material.
Never attempt to fight explosives fires.
Never force explosive materials into a borehole.
Refer to Safety Data Sheet for First-Aid information.
Innopak products should be kept at temperatures between –15°C (5°F) and 55°C (131°F) prior to initiation.
Shelf Life
12 months from date of manufacturing and when stored at temperature conditions between –20°C (–4°F) and 40°C (104°F).
Innopak CXL MS products are only available in Valeron film.
CXL MS case dimensions (L × W × H):
a) 445 mm × 325 mm × 273 mm (17-1/2 in × 12-3/4 in × 10-3/4 in).
b) 850 mm × 250 mm × 184 mm (33-1/2 in × 9-13/16 in × 7-1/4 in).
c) 1067 mm × 940 mm × 787 mm (42 in × 37 in × 31 in).
*Nominal gross case weight: 25 kg (55 lb).
**Nominal gross case weight: 26 kg (57 lb).
***Nominal gross case weight: 27 kg (60 lb).
Woven Shot Bags
Case dimensions (L × W × H):
1067 mm × 940 mm × 787 mm (42 in × 37 in × 31 in).
All explosives must be transported in accordance with local, state and federal regulations.
Class 1.5 D, PG II, UN 0332, EXPLOSIVES, BLASTING, Type E.
In case of emergencies, click here to contact our team for assistance.
Omnia disclaims all liability whatsoever, whether arising in contract, delict (including negligence) or otherwise in relation to the use of any products/solutions or services and all implied warranties, terms and conditions relating to the products/solutions or services (whether implied by statue, common law or otherwise), including (without limitation) any warranty, term or condition as to accuracy, completeness, satisfactory quality, performance, fitness for purpose or any special purpose, non-infringement, information accuracy, as between Omnia and you, are hereby excluded. Omnia specifically disclaims liability and will not be responsible for, any liability or damages, howsoever arising, resulting from the use or reliance upon the information in this document.
You assume sole responsibility for results obtained from the use of the products/solutions or services, and for conclusions drawn from such use.
We continuously update our technical data sheets to reflect the most current and accurate information based on the latest available data. As such, the information provided is subject to revision. We recommend regularly checking for updates to ensure you are accessing the most up-to-date technical details.
